• Address:

    26 Elizabeth St, South River, NJ 08882

  • Email:

    mail@truck-repair-nj.com

  • Phone line:

    +1 (347) 656-62-73

A mark inside the hood can change the scope of an FL112 cooling-system repair. Replacing a leaking connection is only part of the answer if the upper pipe is also touching the hood. The repair needs to account for the space occupied by both assemblies.

For Freightliner FL112 repair in South River, NJ, contact Truck Repair Shop. Our radiator service covers coolant-leak assessment and repair or replacement needs. The examples below focus on three shortcuts that can leave the original fit problem unresolved.

FL112 coolant pipe repair: look beyond the paint

AI illustration of an uninstalled curved metal coolant pipe
AI illustration of an uninstalled coolant pipe; geometry varies with the fitted assembly.

Mistake: treating a rub mark as a paint-only job. Freightliner’s June 1999 bulletin 20–37 describes contact between an upper radiator pipe petcock and the hood underside. It identifies pipe positioning or hood adjustment as possible contributors.

Ask for the point of contact to be identified before discussing a cosmetic finish. A useful repair conversation distinguishes the marked panel, the part touching it and any cooling-system damage found. Those are different findings; the appearance of the hood alone cannot settle the whole estimate.

Mention recent work involving the hood, radiator or connecting pipe. A photograph taken safely while the engine is off can help show the location, but it should not replace the inspection. Do not reach into a running engine compartment to collect one.

Match the evidence before applying the bulletin

The bulletin’s stated scope is FL112 trucks with Caterpillar C10 or C12 engines built before November 13, 1998. It describes a later factory pipe design, too. Neither the FL112 badge nor a matching photograph establishes which pipe is on a truck today.

Keep engine names separate in your service request: Cummins L10, M11 and ISM; Caterpillar 3176, C10 and C12. This page’s specific hood-contact example concerns the early C10/C12 arrangement. It is not a shared fitment instruction for those other engines.

A bottomed pipe can create a different problem

Mistake: pushing the pipe down and leaving it against the housing. In the documented early arrangement, the pipe end must remain separated from the thermostat housing. That separation is distinct from the clearance above the pipe.

A request to “move it lower” leaves out an important part of the job. Ask which fitted connection will be repositioned, whether the existing pipe is suitable and what condition the surrounding hose and clamps are in. The estimate should describe the affected parts rather than use “adjustment” as a catch-all.

Our truck radiator service addresses leaks and related connections as part of the cooling complaint. If you have already bought a pipe, bring its identification and the previous invoice. We can discuss it against the findings before agreeing on the work.

FL112 hood clearance must be judged closed

AI illustration of a light scuff on a composite truck hood underside
AI illustration of a scuffed composite hood underside, not a customer vehicle or a model-specific clearance guide.

Mistake: accepting the view with the hood raised as proof of fit. The bulletin checks clearance with the hood lowered and latched. For its specified old-style arrangement, insufficient clearance after positioning leads to a different pipe design.

Keep two questions on the repair handover: was the identified contact addressed, and were the disturbed coolant connections checked for leaks? A dry connection does not, by itself, explain what happened to the contact point. Likewise, improving the visible gap does not answer a coolant-loss complaint.

Tell us separately if the truck has also overheated or repeatedly needed coolant. That information changes the cooling complaint being assessed. Arrange the visit before setting out; steam, active coolant loss or a temperature warning calls for a safe stop rather than another trip to see whether the mark returns.

A corrected drawing changes the decision

Use the June 1999 revision of bulletin 20–37 rather than the earlier May version: Freightliner corrected a measurement. Apply it only to the hardware it describes.

For your records, request a clear description of what was adjusted or replaced. Keep it with the part information and the original reason for the visit. If the concern returns, that record is more useful than an invoice that says only “coolant repair.”

Call (347) 656-6273 to discuss your FL112 cooling concern. Workshop location: 26 Elizabeth St, South River, NJ 08882. Our contact page provides directions and visit information. Explain whether you are booking for a leak, a contact mark, or both, so the proposed assessment addresses the actual complaint.


Service terms


  • CLEAR ESTIMATES

    Inspection findings, the proposed work and the estimate are discussed before repairs begin.

  • PARTS OPTIONS

    We agree on suitable parts for the engine, the work and your budget.

  • FREE DIAGNOSTICS WITH REPAIR

    Diagnostic work is free when you proceed with the repair.

  • WARRANTY FOR WORK

    Our repairs carry a warranty. We explain the terms that apply to your job.

Congratulations. Your message has been sent successfully.
Error, please retry. Your message has not been sent.

By submitting this form, you ask us to use the information you provide to respond to your inquiry. See our Privacy Policy. This does not sign you up for marketing.


Your Privacy Choices

Essential site functions and the cookie that remembers your privacy choice stay available.

Cookie Policy · Privacy requests and information

Call: (347) 656-6273