• Address:

    26 Elizabeth St, South River, NJ 08882

  • Email:

    mail@truck-repair-nj.com

  • Phone line:

    +1 (347) 656-62-73

Truck Repair Shop provides diesel head gasket repair and replacement in South River, New Jersey. The gasket seals the joint between the cylinder head and engine block. When that seal is damaged, the repair needs to address both the failed joint and the conditions that caused the problem.

We assess the symptoms, discuss the findings and agree on the work before repairs begin. Call (347) 656-6273 with your truck and engine details to arrange an inspection.

Diesel head gasket diagnosis in South River

Illustration of an inline-six diesel cylinder head gasket
Illustration: an inline-six diesel head gasket.

Repeated overheating, unexplained coolant loss, persistent white exhaust or fluid contamination are reasons to arrange an assessment. They do not establish a blown head gasket on their own. The engine configuration and the pattern of the complaint determine the next checks.

Tell us whether the temperature rises under load, whether coolant needs topping up and whether the problem followed an earlier repair. Warning messages, recent service records and details of any overheating incident help guide the investigation.

Before major disassembly, the assessment may include cooling-system pressure checks and application-specific checks for internal leakage. Bubbles, unusual pressure or contamination must be considered alongside the other findings before the cylinder head is removed.

Find the cause before fitting parts

A damaged hose, cap, cooling fan or radiator can contribute to a cooling complaint. On engines equipped with a cooled EGR system, the EGR cooler is another possible source of internal coolant loss. A damaged gasket, cracked casting and other engine-specific leak paths can require different work.

If overheating has damaged the sealing joint, replacing the gasket while leaving the cooling fault unresolved can expose the engine to the same conditions again. Our truck radiator service covers related assessment when the findings point to the radiator or its connected cooling system.

Head gasket replacement: what the job involves

Illustration of a diesel cylinder head sealing surface and straightedge
Illustration: cylinder head surface inspection.

The access required depends on the engine and truck installation. Intake, exhaust, fuel-system and valve-train components may be involved. We explain the planned removal work and the findings that could change the scope.

  1. Identify and prepare. Establish the engine specification, select the applicable service procedure and prepare the surrounding systems for disassembly.
  2. Remove and assess. Examine the gasket, head and block sealing areas, along with related components affected by the failure.
  3. Fit the specified parts. Use the correct gasket and required fasteners, following the engine's installation sequence and settings.
  4. Reassemble and verify. Complete the applicable adjustments and fluid-filling procedure, check for leaks and assess temperature behavior and the original complaint.

The initial diagnosis and the findings after removal are separate stages. If disassembly reveals additional damage, we discuss the revised repair plan with you before proceeding.

Surface condition and fasteners matter

A new gasket cannot correct a cracked casting or a sealing surface outside its specified limits. Flatness, surface finish and the condition of the head and block must suit the engine and gasket design. If a surface needs further work, that becomes part of the repair discussion before reassembly.

Fastener requirements also vary. Torque-to-yield bolts require replacement where used; other fasteners must meet the application's inspection and reuse rules. Tightening sequence, torque, angle stages and lubrication requirements must follow the relevant procedure rather than a setting taken from another engine.

Truck cylinder head repair and replacement

If inspection identifies damage beyond the gasket, the condition of the cylinder head affects the next decision. The job may need additional assessment or a compatible replacement casting. We discuss the findings, suitable parts and associated work so the estimate reflects the engine's condition.

For information specific to Volvo trucks, see our Volvo head gasket service. The engine model and serial information remain important: the truck's brand alone does not define the gasket, head or installation requirements.

What affects the cost and turnaround?

Diesel head gasket replacement cost depends on access, the engine specification and the damage found. Gaskets, fasteners, associated seals, fluids and any necessary head or cooling-system work all affect the scope. Parts availability and additional findings also influence the schedule.

A useful estimate separates diagnosis and removal from the replacement parts, associated repairs, reassembly and completion checks. We explain the proposed work and discuss changes before extending the agreed repair.

Arrange an inspection

Have the VIN, engine model and serial number, warning messages and repair history ready. Mention repeated coolant additions, fluid contamination and previous overheating. Follow the vehicle's warning instructions and arrange assistance if continued operation could cause damage. Do not open a hot, pressurized cooling system.

Contact Truck Repair Shop at (347) 656-6273 to arrange service at 26 Elizabeth St, South River, NJ 08882. We will assess the concern and help you plan the required repair.


Service terms


  • CLEAR ESTIMATES

    Inspection findings, the proposed work and the estimate are discussed before repairs begin.

  • PARTS OPTIONS

    We agree on suitable parts for the engine, the work and your budget.

  • FREE DIAGNOSTICS WITH REPAIR

    Diagnostic work is free when you proceed with the repair.

  • WARRANTY FOR WORK

    Our repairs carry a warranty. We explain the terms that apply to your job.

Congratulations. Your message has been sent successfully.
Error, please retry. Your message has not been sent.

By submitting this form, you ask us to use the information you provide to respond to your inquiry. See our Privacy Policy. This does not sign you up for marketing.


Your Privacy Choices

Essential site functions and the cookie that remembers your privacy choice stay available.

Cookie Policy · Privacy requests and information

Call: (347) 656-6273