• Address:

    26 Elizabeth St, South River, NJ 08882

  • Email:

    mail@truck-repair-nj.com

  • Phone line:

    +1 (347) 656-62-73

Keep the recovery record with an FLD112 repair request. A shifting problem reported after transport needs a timeline: what had already failed when the truck stopped, and what changed between pickup and arrival.

Truck Repair Shop handles Freightliner transmission and chassis assessment in South River, NJ. The conditions below explain why the transport history matters to a repair discussion.

FLD112 transmission trouble with the engine off

AI illustration of a generic helical transmission gear
AI-generated illustration of a generic transmission gear; not an identified FLD112 part.

For a truck fitted with a covered Fuller manual transmission, engine-off transport can create an unusual lubrication condition. Eaton’s RWRG0037 describes the mainshaft being driven by the road wheels while the front-box gearing remains stationary. Oil distribution and splash in that section differ from normal engine-driven operation. The resulting heat can damage mainshaft gears and washers.

The important details are whether the drive wheels rolled and whether the axle shafts or driveshaft remained connected. A note saying only “towed in neutral” does not establish which transmission components rotated. Eaton’s troubleshooting guide addresses protection by interrupting that drive path or keeping the drive wheels off the road.

Eaton lists difficult lever shifts and inability to select front-box gears among symptoms associated with the documented damage. Those observations call for assessment; they do not prove how a particular failure occurred. Our truck transmission repair service examines the affected function and discusses the work supported by the findings. This Fuller explanation must not be applied automatically to another gearbox design.

An axle-shaft opening needs protection

AI illustration of a generic six-hole hub closure plate
AI-generated illustration of a generic hub closure plate; dimensions and fitment vary.

Removing an axle shaft introduces another service boundary. Freightliner’s FLD recovery instructions call for covering the exposed hub ends to retain lubricant and exclude contaminants from the wheel bearings and axle oil. A recovery record should identify which shafts were removed and how the openings were protected.

Oil around a wheel end after arrival needs its escape point located and the disturbed assembly checked. Lubricant loss, contamination exposure and a leaking reassembled joint are different findings. The appearance of oil alone does not establish bearing damage.

If the driveshaft was disconnected instead, include that operation and its reconnection in the history. Our truck driveline repair service covers related shaft and joint concerns. Tell us which work was actually performed rather than treating axle-shaft removal and driveshaft disconnection as the same operation.

Raised drive wheels address one risk

Keeping the drive wheels off the road removes the wheel-driven rotation discussed above. It does not establish that every lifting arrangement suits the complete truck. The FLD driver’s manual, for example, prohibits a rear towing hookup on vehicles with a roof fairing because wind loading can damage the cab.

A gearbox-protection instruction does not approve the complete lift. The recovery operator must follow vehicle-specific limits, including the body equipment.

For a repair enquiry after transport, existing photographs of the hookup and removed parts can help identify the conditions involved. Use records already available; do not move or dismantle the truck to reconstruct the event.

Record the recovery as its own event

Send a short arrival note that separates the breakdown, transport and newly reported concern:

  • What stopped the truck, and whether gear selection was already affected.
  • Which wheels stayed on the road, whether the engine was off, and what remained connected.
  • Which shafts or covers came off, and what was refitted before arrival.
  • The first new symptom after transport, with the recovery paperwork or existing photographs.

Identify the truck as FLD112 or FLD112SD as recorded. For an engine-related enquiry too, retain the installed family name: Cummins M11 or ISM, or Caterpillar 3176/3176B, C10 or C12. These identifiers help describe the vehicle; they do not select its transmission or establish the cause of a post-transport fault.

Arrange the FLD112 assessment on (347) 656-6273 and explain that the truck has been recovered. Visit our South River workshop: Truck Repair Shop, 26 Elizabeth Street, NJ 08882. We can review the original breakdown and the transport history as separate parts of the repair request.


Service terms


  • CLEAR ESTIMATES

    Inspection findings, the proposed work and the estimate are discussed before repairs begin.

  • PARTS OPTIONS

    We agree on suitable parts for the engine, the work and your budget.

  • FREE DIAGNOSTICS WITH REPAIR

    Diagnostic work is free when you proceed with the repair.

  • WARRANTY FOR WORK

    Our repairs carry a warranty. We explain the terms that apply to your job.

Congratulations. Your message has been sent successfully.
Error, please retry. Your message has not been sent.

By submitting this form, you ask us to use the information you provide to respond to your inquiry. See our Privacy Policy. This does not sign you up for marketing.


Your Privacy Choices

Essential site functions and the cookie that remembers your privacy choice stay available.

Cookie Policy · Privacy requests and information

Call: (347) 656-6273